What you need to know when buying a chandelier?
No matter where You buy the chandelier in the market, or in an expensive store. The only difference in cost. Hung from the chandeliers every day and every time a marriage. Several defects in each chandelier. If the wires short or not soldered or confused, this can be resolved, the soldering iron is always with me. And if problems with the thread? The diameter of the nuts does not match the diameter of the tube of the horn. And if the hole in the glass ceiling more than a nut? Earlier, each cartridge was a counter nut, now they are gone and light bulbs vivenciada together with cartridges. Earlier in the cartridge inserting threaded under the bulb was made of steel or brass, now aluminum foil covered under color of brass. Before electric cartridges were made of heat-resistant Evonik, now of thermoplastic, melt when heated. Some chandeliers are no wires. And if the shades have different weights, the chandelier will hang crooked. And chandeliers led - nightmare. Three hundred LEDs connected in series, at least half a hundred twists and not one soldering. If You choose a chandelier, try to tighten the bulbs in each cartridge, they should not fall out. Plastic nut for fastening ceiling should tightly screwed onto the cartridge. The connecting wires must be included. If the chandelier has a large number of halogen light bulbs, ask to be included. Step-down transformer inside chandeliers under load should not buzz.
Before you hang a chandelier, be sure to check the reliability of the hook
slightly pull it.
If the chandelier is attached to the ceiling by means of the bracket.
Determine the direction wiring, position the bracket so that when drilling the ceiling not to get into the wire. Do not drill the ceiling in the place where set the hook. The wire is very often a loop wound on the hook and the hole filled with plaster. You need to step back a bit and drilling no plaster, and concrete. Do not drill a thick brown, max 6 mm Screws and dowels included in the kit as a rule not suitable for mounting chandeliers, they need to be replaced. Before screwing the bracket to the ceiling, you must install the screws and secure them with the help of nuts. If the hook prevents, it needs to be cut down. In order not to damage the wires do not hit the hammer on the hook.
Do not attach the chandelier to the hook by means of laces or gum from pants
so, how do bureaucratic colors electricians.
How to connect a chandelier.
The first thing you need to deal with wires. If on the ceiling, 2 wire, no problem. voltage is-awesome. And if 3 wires, and a switch double. Conventional light-screwdriver to check is no good. Not always the phase goes through the switch, sometimes the wires mixed up and not connected zero gives a tip that lights up as phase. Need 2 dupouy probe. Include the first key looking for the voltage, we find three wires and a couple mark. Turn off the first included the second key, find a couple, mark. On one wire came out 2 marker, it will be total. And so with the wires figured out. Start chandelier. For example, the chandelier has 6 lights, but you need to divide by 2 and 4. The first thing you need to ring all the wires for an open or short circuit. This requires measuring device. I use a probe with a sound generator. Then from each cartridge take one wire, connect them in place. This is the common wire chandeliers. Hardly you will be able to plant 6 wires on one clemo and twisting will not provide good contact. This is the best wire to solder. This requires a soldering iron not less than 60 Wat. (in Soviet times in chandeliers all cables were soldered) Then select the 2 wires and connect them the same way. The remaining 4 wires also connect. Got 3 end. Plug. If when you turn off the switch voltage is not present between the wires and between the hook and wires, then twist the tube does not need. If between hook and wire voltage is present, then the phase is connected directly by switch. Zaizolirovali hook. If the connection you have decided to use the terminal block know, the ends of stranded wires should be soldered, otherwise the screws Kremnica passing a thin strands of wire. If Kremnica no, I do not advise to do the twisting. Clean the wire inch and a half, tightly-wound multi-conductor wire from the chandelier, bend and crimp. Common wire chandeliers connect with the General on the ceiling, the remaining 2 wires connect to the two on the ceiling in any sequence and insulate. Nibble switch, if nothing happened, then a short circuit and no, you can screw in a light bulb. One key will include 2 bulbs, the second 4, and the two together 6.
Never connect the chandelier without checking what's on the inside!
Have a single switch and two wires on the ceiling. How to connect a chandelier that would light bulbs included separately? Install the chandelier additional switch. For example:
Trerotola chandelier, one light bulb connected directly, through two additional switch on the chandelier. Turn on the light - joined one bulb. Pull for the strap joined the second, pull again joined the third.
Source:
here
No comments:
Post a Comment