Replacement shells
The diversity of modern washbasins comparable only with the number of design ideas. From round shape to the geometric combination of cubism and the usual oval bowls to monolithic countertops with recessed drain. Symmetric and asymmetric, coaxial and angular.
But all it's many forms, however, can be grouped into three or four groups according to the method of installation and mounting. This setting on the tables, stands and pedestals, shelves attached to the wall, and on the brackets and simply attached to the wall on the bolts with decorative polypedilum.
In addition, sinks come with holes for faucets and without them, if the mixer is arranged in the wall. Holes is three and one. Three holes for faucets with separately inserted valves for hot and cold water and water spout.
Set washbasin on pedestal
Cabinet put in the bathroom or toilet in the planned location. Cutout countertop stack the sink and into the drain hole of the sink insert grid drain with a rubber gasket. Under the sink drain grate tighten nut. Pipe drain gratings put on the locking nut with a wedge-shaped locking ring. Attached to the pipe a glass siphon, pressed against the locking ring and screw up the siphon locking nut. If a bypass pipe of the siphon is not crimped and not flexible, then disconnect it from the siphon.
To connect the drain pipe to the sewer system must rubber sealing ring with an outer diameter of 70 mm and an inner smaller diameter outlet pipe siphon - 35 mm Open socket sanitation by removing the tube or gag is inserted into the socket until it stops rubber sealing ring, and the ring insert the discharge pipe of the siphon. The pipe, if it has been disconnected from the siphon, screwed in place on the glass clamping nut.
In the sink pour water and check for leaks. If you encounter proteci, stronger clamp nuts in places leaks.
If the sink has a hole faucet, faucet installation is carried out in the following order. Mount mixers happens on the retainer nut and u-shaped bracket. Mixer strip is inserted into the hole and bottom tighten a nut or a horseshoe, pre-placing them under the spacers with washers. U-shaped bracket is screwed a nut to the stud mounted in the bottom of the mixer. Similarly installed and washbasin on a stand.
Set washbasin on pedestal
Set wash basins with pedestal, or wall with attaching the sink to the wall or outside the wall by attaching the pedestal to the floor, and sinks to the pedestal. Consider installing on the podium at the wall.
The pedestal put in the planned location at the wall, install the sink on a pedestal so that the drain hole is located above a center of the base. Tightly to the wall pulling the sink and pencil mark the attachment points on the wall, putting his pencil through the mounting holes under the sink.
Push the pedestal sink with side or remove only the sink and drill with women's drill drill holes for fasteners. Into the holes of the driven tube, return to the wall washbasin, aligning the mounting holes shell with holes in the wall. On dowels or screws wear cushioning washers and fasten the sink to the wall with a wrench.
In any case, do not tighten the screws - the washbasin can burst, enough to tie so that it does not staggered.
Then to the sink attach the drain trap and discharge pipe of the siphon with the o-ring is inserted into the socket of sewage. If included with the sink goes faucet, then carry out the appropriate installation.
Set washbasin on brackets
To install the sink on the brackets, you must first hold a markup on the wall.
At the height of 800-850 mm from the level of net floor on a wall with a long straight rail and construction level, mark a horizontal line. This line-level sink. Measure the thickness of the side edges of the sink, which he will rely on the brackets. The number you lay down from a horizontal line and mark on the wall.
The same mark is doing with the other hand under the horizontal line and mark connect direct. The received level of the mounting brackets. Turn the sink upside down, mounted on its lateral support planes upside down reference plane of the brackets and have them as they will have to support the sink. Measure the distance between the longitudinal axes of the brackets. The resulting number lay on the line level mounting brackets. These marks are longitudinal axis of the mounting brackets.
The brackets are put to the wall by aligning the reference plane of the bracket line bracket level, and a longitudinal axis with an axial marks on the wall and mark with a pencil the point of mounting through holes of the brackets. Drill drill holes, hammer tube and fasten the seat brackets.
The brackets installing the sink, and the bottom mark the places of attachment of the shell itself. Drill drill holes, drive tube and setting the sink in place, screwed plugs with a wrench. The dowels must wear cushioning washers and tightening dowels are doing enough to sink did not stir.
After completion of the mounting brackets and sink to sink down the drain with the hydraulic valve and the outlet pipe. Installation of siphon carried out as previously described (see also the section where it says about installing on the stand). If included with the sink comes with a mixer, then set the mixer and connect it to the water. Then pour in the sink water to zavodnici water siphon and check the drain for leaks at the connections.
Set washbasin on the hanging shelf
This method of installation sink has several practical items. Regiment assumes the reference load instead of brackets, plays a support role for toiletries, and a double (two-storey) regiment closes under the sink drain system and can be used as a storage space for towels, detergents and toiletries.
Installation washbasin with shelf is held in this order: first on the wall in the planned location notes the level of installation shell (800-850 mm from the level of net floor), put the bowl flat face to the wall, aligning with the level line installation, and mark a pencil under the sink where it is mounted.
Leaving the shell side, according to the planned point drill drill holes and drive them in the tube, put to the wall of the sink in place and screw plugs with sealing washers.
Further, under sink conduct markup mounting shelves. A shelf placed symmetrically or asymmetrically relative to the centerline of the sink, placing a center axis or by moving right or left.
First regiment put under the sink to the wall, keeping a horizontal position with the help of a level. Mark on the wall attachment point, putting the pencil in the eyes of the mounting holes. Not taking away the shelves from the wall, marked on its upper surface through the drain hole of the sink place inlet of the drain pipe.
The shelf is put aside, drill drill rack in the center of the projected circle. Then in the drill Chuck insert instead drill a special nozzle-holder for rifenbary (cafebar a special cutting tool for drilling holes of large diameter in the form of a core drill that cuts the material, unlike a drill, only in the annular space at the walls of the hole). In the nozzle fix sevenbar right diameter (35 or 44 mm) and drill, which is scheduled the center of the hole in the shelf.
Direct the drill bit in the center of the hole and make drilling zevenboom. If the shelf is two-storied, then this tool cut in the bottom shelf hole for the drain pipe, making the appropriate markup in the right place bottom shelf. If there is no such tool, the holes do in the shelf using vydalblivanija chisel and matting round rasp.
If included with the sink has a faucet before installing shelves hold the mounting of the mixer. Mixer strip is inserted into the hole in the top of the sink and below the plane of the fixed clamping nut with gasket and washer or clamp bracket by tightening its nut to the stud of the valve. To provide water supply to the mixer in a shelf cut corresponding holes.
You can then attach the shelf to the wall. Drill drill in the wall marked the holes, hammer them in the tube and, having prepared dowels and keys down the shelf under the sink. Make holes in the shelves of the mixer tube, tightly grip the shelf to the wall and the sink, and make sure the drain hole in the sink with a hole in the shelf, and screw to the wall with anchors.
If the eyelets in wide shelf, dowels wear appropriate washers. Under a shelf having a trap in the drain hole of the sink insert the drain pipe below the drain pipe wear of the sealing ring and the extension.
Holding the drain pipe, push the extension tube with the ring through the hole in the shelf and tighten a pipe clamping nut on the pipe put on the nut with locking ring and the siphon. Tighten the nut on the siphon, the siphon fasten the discharge pipe and connected to the socket sanitation.
Set washbasin on prophetical
To install the sink on prophetical only if sewer pipes embedded in the wall, and the mouth of the drain outlet is located in the wall at a height of not less than 0, 5 m from the level of pure sex.
Then as usual secure the sink to the wall, hold the mounting of the faucet and drain system, a mixer connected to a water supply system, and siphon - drain, and excess bypass pipe cut with a handsaw.
After that, attach the trap cover on pre-mounted into the wall studs. Trap cover tightly pressed to the wall and the sink, and make sure the eyes with the heels, through the side window, put on studs sealing washer with flange washer sink in the eyes of the pedestal, navertyvajut the stud nuts and tighten with a wrench. The side Windows are covered by decorative caps.
rem2.ru
No comments:
Post a Comment